Exlex Fins – For Those Interested in the Development of Yacht Design.

Sven Yrvind demonstrates the adjustable G11 epoxy laminate steering fins and scale trunk slots designed for his experimental ocean cruiser Exlex.

In his workshop, boatbuilder Sven Yrvind examines a plate of G11 epoxy laminate designed to steer his experimental ocean boat without a traditional rudder. Developing a balanced hull requires adjustable lateral planes, and Yrvind demonstrates how these fins control the vessel on extended ocean passages.

Holding up the laminate sheet, Yrvind details the measurements: “It’s 105 * 40 cm. And it’s 12 mm thickness. So, it’s very strong and quite heavy to make it sink down.” Rather than making all new units, he has one fin from a previous boat and plans to get three in total.

Fin Geometry and Trunk Slot Adjustments

To demonstrate trimming at sea, Yrvind uses a scale model showing the trunk slots and pivot pin. When fitted into the slot, the fin moves outward at 12 degrees with an angle of attack set at 4 degrees. This alignment keeps the boat balanced on long passages, such as sailing the trade winds where a vessel might run on a single tack for at least 10 days.

The trunk housing supports 30 cm of the 105 cm fin inside the box, leaving 60 cm extending below the hull. The fin can be lifted 30 cm to move into adjacent slots. Near the coast where frequent tacking is needed, Yrvind uses the forward slot, while the aft trunk provides three slot choices to adjust the angle between 10 degrees and 20 degrees for downwind sailing.

Transom Assembly and Atlantic Trials

Yrvind turns to the hull to install the transom. He adds tape along the joint for insulation, removes the clamps, and fastens the piece with screws. The plywood test craft serves as an experimental platform for his planned voyage toward Dunedin.

Reflecting on the sea trials, Yrvind remarks: “And of course the model boat, you know, the experimental one will teach us how it is. We will see if I can get out of the Atlantic, you know.” If funding allows, he plans to tow the boat on a trailer to Ireland and sail into Atlantic waters in July.

Fin and Trunk Specifications

Component FeatureDesign Dimension or Angle
Fin Material & ThicknessG11 epoxy laminate, 12 mm
Fin Overall Dimensions105 cm height by 40 cm width
Trunk Housing Depth30 cm inside support box, 60 cm below hull
Cant and Trim Angles12 degrees outward lean, 4 degrees tack angle

Frequently Asked Questions

What material is Sven Yrvind using for the adjustable steering fins?

Sven Yrvind is using G11 epoxy laminate measuring 105 by 40 cm with a 12 mm thickness, heavy enough to sink down into the water.

How are the fins supported inside the hull trunk?

The 105 cm fin is supported by 30 cm inside the trunk box and extends 60 cm beneath the hull, with the ability to lift 30 cm to move between slots.

How does Sven Yrvind trim the fins for ocean passage making?

The fin slots allow an outward angle of 12 degrees and an angle of attack of 4 degrees, engineered to keep the vessel balanced on trade wind tacks lasting 10 days or more.

Where does Sven Yrvind plan to conduct ocean sea trials?

Yrvind plans to transport the experimental craft on a trailer to Ireland and launch into Atlantic waters in July if funding permits.

Support Sven Yrvind

At WeBoating.com, we profoundly acknowledge the unwavering dedication that Sven Yrvind invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.

We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.

We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "Exlex Fins – For Those Interested in the Development of Yacht Design." video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Sven Yrvind, their collaborators, and the brands they're associated with.

To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.

If you have any feedback, corrections, or additional information about Sven Yrvind or their videos, please use the comment form below to share your thoughts with us.

Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!

This Youtube channel is about me Sven Yrvind. I am 87 and a half years old dyslectic solo sailor.
I am building a plywood test boat for a Divinycell and NM-epoxy high-latitude cruiser.
She will be about 4.8 meter 15 and a half feet long. Her beam will be 1.3 meter. She is a two masted lugger with a total sail area of 6 square meter. She will have no rudder but will be steered by adjustable fins. I am planning a cruise in the Southern Ocean to Dunedin NZ.
Subject to change.
Often the 22th every month I do a resume of the project.
I have an illustrated book with good reviews on Amazon. https://www.amazon.se/s?k=yrvind&crid=1549D6PR18BUJ&sprefix=%2Caps%2C112&ref=nb_sb_ss_recent_1_0_recent
If you’re interested in contributing to my experiments links are below.
https://www.paypal.com/donate/?hosted_button_id=53X8NVEA22MBL
Swish 0706200550
Also please subscribe - even if you are not interested in sailing.
For more see Yrvind.com

Exlex Fins – For Those Interested in the Development of Yacht Design. Location

  • Sven Yrvind Workshop, Västervik, Sweden (57.7587,16.6379)
We will be happy to hear your thoughts

Leave a reply


Latest Episodes from Sven Yrvind

Explore the most recent voyages. Subscribe to the channel to never miss an update!

Showing 1-6 of 1996 results
Using Gravity Clamps for Gluing Locker Covers.
Sven Yrvind

Using Gravity Clamps for Gluing Locker Covers.

Swedish solo sailor Sven Yrvind installs locker push doors and lids, employing gravity clamps to deliver steady downward pressure as epoxy cures in his workshop.
Taking Down My Charts and Talking About Boat Plans.
Sven Yrvind

Taking Down My Charts and Talking About Boat Plans.

This Youtube channel is about me Sven Yrvind. I am 87 and a half years old dyslectic solo sailor. I am building a plywood test boat for a Divinycell and NM-epoxy high-latitude cruiser. She will be about 4.5 meter or 14 feet and 9 inches long, the beam 1.36 meter, 4 feet 6 inches. She is a two mas...
More mocking up.
Sven Yrvind

More mocking up.

Sven Yrvind steps inside a full-scale wooden mockup in his Västervik workshop, assessing bunk clearance, seated headroom, and hatch latches for his ocean test boat.
Mockup – No Ballast, Deckhouse Buoyancy for Self Righting
Sven Yrvind

Mockup – No Ballast, Deckhouse Buoyancy for Self Righting

Inside his Västervik workshop, Sven Yrvind builds interior mockups for his 4.5-meter test boat, testing a stacked two-level living layout and deckhouse reserve buoyancy for self-righting stability without heavy ballast.
The two bulkheads weakly installed.
Sven Yrvind

The two bulkheads weakly installed.

Sven Yrvind evaluates two bulkhead retainer techniques and installs temporary fillets to mock up the cabin layout using oriented strand board in his Västervik workshop.
The Outer Coaming and Fiberglassing the Inner One.
Sven Yrvind

The Outer Coaming and Fiberglassing the Inner One.

Sven Yrvind fits the outer spray skirt coaming and laminates fiberglass onto the inner coaming in his workshop, refining his rope attachment setup and filleting the joint defenses.
Browse All Videos
WeBoating
Logo
Shopping cart