In the boatyard at Bangor, Northern Ireland, Beverley Leigh and Gaynor are deep into haulout maintenance aboard their 2002 Bavaria 36, featured on Sailing Yacht Salty Lass. Working at the stern of Salty Lass, Beverley starts by smoothing down the rudder housing with a Dremel, grinding away a stubborn burr that lingered after initial chisel work. The project marks the start of a demanding round of boatyard maintenance focused on steering gear, ground tackle, and hull preparation before the boat returns to the water.
With the rudder dropped, Gaynor examines the aluminum bearing cup housing and the rudder stock, discovering fine micro-pitting scattered across the metal surfaces. Measuring in mere microns, the tiny indentations can just barely be detected with a fingertip. Cautious about potential wear on the steering system, Gaynor calls over the boatyard manager for an experienced second opinion.
After inspecting the housing, the manager confirms that the micro-pitting is not a operational concern. The outer bearing cup remains largely stationary within the housing, absorbing lateral load only when the hull heels under sail, while active rotational movement takes place within the inner bearing assembly. With the diagnosis settled, the plan is set: clean the aluminum thoroughly before oxidation sets in, pack the cavity with a generous amount of marine grease, and await replacement bearings currently on order with an expected delivery time of about a week.
Moving from the stern to the yard tarmac, Gaynor turns to overhauling the yacht’s ground tackle. She begins by removing all the colored depth markers from the chain links before tackling accumulated grime and salt residue with an ordinary brush and a stiff wire brush. Reversing the chain end-for-end is a regular maintenance routine aboard Salty Lass. The links resting at the bottom of the anchor locker remain perpetually damp and vulnerable to corrosion, while the upper section stays in clean condition. Turning the chain end-for-end every couple of years distributes link wear evenly along its entire working length.
To restore protective zinc coating across the chain, Gaynor lays the cleaned links out on sheets of cardboard across the yard. The crew uses every available can of zinc cold-galvanizing spray before rain threatens. As Gaynor explains, “the galvanizing paint will work much better on the anchor chain if it’s on the anchor chain.” Because residual spray in aerosol cans provides no practical benefit, so the entire batch is coated evenly across the links until the chain looks almost new. After replacing the markers, Gaynor inspects the oversized anchor swivel. Drawing on her professional aviation maintenance background and the principle of reasonable expected lifetime, she plans to replace the swivel in a year or two despite no visible defects, noting that their cruising plans for the season remain local to the marina without anchoring in hostile sea conditions.
The anchor itself requires targeted surface repairs. One of the vessel’s two previous owners had drilled a hole directly through the anchor shank, piercing the original galvanized layer and compromising any manufacturer guarantee. Previous attempts to protect the raw metal with Hammerite paint lasted barely 10 minutes. The crew uses a drill to ream out surface rust from the drilled hole, treats the steel with rust converter, and applies zinc galvanizing spray across both the shank hole and the scarred anchor tip, which sustains repeated abrasion against seabed debris before setting.
Beneath the hull, Gaynor inspects a spot of rust bleeding along the keel joint where the structure rests on the yard blocks. Using a hand file, she abrades the oxidized surface metal down to clean steel and applies chemical rust converter deep into the interface. Hull painting is coordinated around the yard’s hoist schedule. Because Salty Lass must be suspended in travel-lift slings to reinstall the rudder stock into the hull tube, the crew plans to wash and roll antifouling onto the masked hull bottom while in the hoist slings, followed by a final wash and topcoat application on launch day over the five coats of existing bottom paint.
Waterline aesthetics receive attention alongside structural maintenance as Beverley repaints the boot stripe. To achieve sharp lines, she implements a masking technique learned from Andy on the Boatworks Today channel, applying high-adhesion masking tape and pulling it away promptly at the end of the painting process rather than leaving it to bake in place. Aboard Salty Lass, maintenance responsibilities are divided by shipboard territory: Gaynor oversees the port side, while Beverley manages the starboard side.
Taking charge of the port tape removal, Gaynor peels the strip cleanly away in a single, continuous sweep from bow to stern, noting that “it was one pull from the front of the boat all the way to the back.” Beverley follows on the starboard side, leaving clean paint boundaries along the hull.
The final mechanical task centers on the upper rudder assembly, which represents the last untouched mechanism aboard the vessel after years of systematic refitting. Disassembly begins by removing the six screws securing the upper deck plate, followed by the four screws holding the stack in place. Lifting the collar reveals a layer of yard grit that had settled underneath the plate within just one week on the hard. However, the plate itself remains stubbornly immovable, glued fast by heavy applications of polyurethane Sikaflex adhesive applied during previous ownership.
The crew spends hours attempting to break the Sikaflex seal from the cockpit, using scrapers, screwdrivers, and levers to pry the plate upward without success. Exhausted by the lack of progress, Gaynor suggests that Beverley go below into the aft cabin to see if the stack can be driven upward from underneath. Moments later, Beverley discovers the underlying engineering design: the lower rudder bearing does not pull upward through the deck plate at all, but extracts downward from beneath the hull.
After positioning the lower bearing from below, a couple of light taps with a screwdriver release the component instantly. The realization sparks laughter through tears on deck as Beverley points out that “This bearing comes out from the bottom.”
With the stubborn bearing extracted, Gaynor prepares the hardware for reassembly, kneeling on the cockpit sole to coat each fastener thread with yellow Duralac anti-corrosion barium chromate paste. The chemical barrier is essential to prevent galvanic corrosion between the stainless steel screw threads and the aluminum cap, while also providing necessary thread lubrication.
Even with Duralac applied, driving the screws into the housing proves physically demanding due to dried sealant residue clinging inside the internal thread channels. Beverley observes the heavy mechanical resistance: “Although we’ve cleaned out all the threads, I think there’s still a ton of silicone in and around them. And even though we’ve lubed everything with Duralac, it’s just very, very stiff.” By carefully backing the screws in and out, the crew ensures clean thread engagement and long-term galvanic isolation across the steering gear.
Gaynor and the boatyard manager determined that the outer bearing cup experiences minimal rotation and only takes pressure when the boat heels under sail. Because the active movement occurs inside the bearing itself, minor pitting on the aluminum cup does not compromise operation once packed with fresh grease.
The chain resting at the bottom of the anchor locker stays damp and exposed to moisture, while the chain near the top remains in good condition. Reversing the chain end-for-end every couple of years balances out cumulative link wear and extends the working life of the ground tackle.
One of the boat’s two previous owners had drilled a hole in the anchor shank, damaging the original galvanized coating. The crew cleaned out the hole with a drill, treated the surface with rust converter, and coated the shank and anchor tip with zinc cold-galvanizing spray.
After spending hours attempting to pry the deck plate upward against heavy Sikaflex adhesive, Beverley checked from inside the boat and realized the bearing is designed to drop out from beneath the hull. Once aligned from underneath, a couple of light taps with a screwdriver released it immediately.
Duralac anti-corrosion paste was applied to the stainless steel screw threads before driving them into the aluminum cap to prevent galvanic corrosion between dissimilar metals and to lubricate the tight, silicone-fouled threads.
At WeBoating.com, we profoundly acknowledge the unwavering dedication that Sailing Yacht Salty Lass invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.
We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.
We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "NOT Sailing Northern Ireland - Rudder repair - anchor chain - keel - Ep. 397" video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Sailing Yacht Salty Lass, their collaborators, and the brands they're associated with.
To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.
If you have any feedback, corrections, or additional information about Sailing Yacht Salty Lass or their videos, please use the comment form below to share your thoughts with us.
Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!
If you like our videos, you can always drop a tip in our coffee jar
https://ko-fi.com/sailingyachtsaltylass
ABOUT US
We have begun a liveaboard adventure on our Bavaria 36, Salty Lass. It is our ongoing mission to explore strange new ports, to seek out new to us cuisines and cultures, to boldly go where the wind takes us and like it
FOLLOW US
http://www.saltylass.co.uk
https://facebook.com/salty.lass.1
https://instagram.com/sy.saltylass
MUSIC
Explore the most recent voyages. Subscribe to the channel to never miss an update!