Boat Maintenance Woes: Technical Difficulties with the Watermaker & Auto Helm
You know what they say: “BOAT” stands for “Break Out Another Thousand.”
While we were anchored in the Dry Tortugas, I got our Spectra watermaker back online. This week, back in Key West, we’re troubleshooting an issue with the feed pump pressure switch, which cuts the watermaker pump in and out depending on the pressure. Unfortunately, the replacement piece is expensive—and it won’t get here anytime soon. In the meantime, I can bypass the switch, as long as I keep a tight eye on the pressure. Boats, man—it’s always something!
In between troubleshooting the watermaker and getting ready to sail north for the summer, Robin and I found time to enjoy a sunset cruise aboard the Schooner Hindu. Schooner Hindu is a lovingly restored and historically significant 1925 gaff-rigged schooner with a rich maritime history. It sails out of Provincetown, MA in the summer, and Key West in the winter. Captain Josh sailed us right past Arabella, giving us a unique perspective on our own gaff-rigged wooden sailboat!
But, back to boat maintenance…
Installing the rudder feedback sensor presented a new challenge. It’s incredible how much I needed to deconstruct just to get that installed properly.
Now, mounting the bracket for the auto helm. The bracket is made of anodized aluminum, which gets mounted to a stainless bracket with stainless steel boats. That means I need to isolate and protect the bracket from corrosion. I chose to use Tef-Gel, which is a corrosion eliminator. The other important consideration is that, if we were to lose the bolts, there’s a good chance we would also lose the auto helm. As a backup, I drilled small holes into each bolt, where I can thread a ring through to prevent the bolts from working their way out.
Now that the above-deck electronics for the auto helm are hooked up, it’s time to go down below and get the system wired and set up down there. The Garmin Reactor 40 needs to be mounted near the center of the boat. This device gives us information about how the boat is moving in space and time.
Now, the auto helm came with a 40 amp breaker—but that didn’t fit into our breaker panel. After speaking with a marine electrician, I feel confident that a 20 amp breaker will do the trick just fine. With this final piece in place, we’re ready to test the auto helm under sail!
Unfortunately…more technical difficulties.
Somehow, installing the auto helm threw off the header sensor and wind reader. Fortunately, our marine electrician friend, Bob, might be able to help…
In the meantime, I took the chance to work on a small project: building a screen drop board to use when it’s hot and buggy. Our acrylic drop board is great, but it doesn’t help much with ventilation—and it’s getting HOT down here in the Keys. I drafted up a shopping list and hit the bricks for a walk to the hardware store, and fun, low-stress, no-surprises project for a change!
--------------------------
Sign up for our email newsletter: http://eepurl.com/hn3Qyv
Acorn to Arabella started as a wooden boat building project in Granby, Massachusetts. Steve began the journey as an amateur wooden boat builder crafting a 38' wooden sailboat in his backyard: designer William Atkin's Ingrid with a Stormy Petrel's gaff rig. These videos follow the journey from tree felling, to lumber milling, to lofting, to the lead keel pour and now sailing the boat—sharing details of the woodworking, carpentry, metal smithing, tool building, and tool maintenance that traditional wooden boats command. This ultimate DIY project continues beyond the boat shop, as Steve and crew travel and learn to cruise aboard the handmade wooden boat that they've built. Just kidding about all that, this channel is about a Siberian Laika named Akiva.
--------------------------
If you are interested in supporting/helping here are a few ways:
https://www.acorntoarabella.com/how-to-help
Acorn to Arabella's wishlist:
https://www.acorntoarabella.com/wishlistpriority
TotalBoat supports A2A! Please consider using our Total Boat referral code. Click here, then shop: https://www.totalboat.com/acorntoarabella They'll kick 10% our way!
To offer recurring support via Patreon, CLICK BELOW. Just $5 a month gets you an invite to our monthly patron-only livestream Q&A sessions!
https://www.patreon.com/acorntoarabella
Original Soundtrack available at benfundis.bandcamp.com
FOLLOW US:
Patreon: https://www.patreon.com/acorntoarabella
Instagram: https://www.instagram.com/acorntoarabella/
Facebook: https://www.facebook.com/acorntoarabella
Website: http://www.acorntoarabella.com
Acorn To Arabella
Steve Denette: The 5th-generation farmer who built the 38ft wooden ketch Arabella from the stumps of his family farm, now pioneering big-wall climbing in Newfoundland.
Channel Information:
Social Media Links:
Support Acorn To Arabella
At WeBoating.com, we profoundly acknowledge the unwavering dedication that Acorn To Arabella invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.
We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.
We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "Boat Maintenance Woes: Technical Difficulties with the Watermaker & Auto Helm" video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Acorn To Arabella, their collaborators, and the brands they're associated with.
To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.
If you have any feedback, corrections, or additional information about Acorn To Arabella or their videos, please use the comment form below to share your thoughts with us.
Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!
You know what they say: “BOAT” stands for “Break Out Another Thousand.”
While we were anchored in the Dry Tortugas, I got our Spectra watermaker back online. This week, back in Key West, we’re troubleshooting an issue with the feed pump pressure switch, which cuts the watermaker pump in and out depending on the pressure. Unfortunately, the replacement piece is expensive—and it won’t get here anytime soon. In the meantime, I can bypass the switch, as long as I keep a tight eye on the pressure. Boats, man—it’s always something!
In between troubleshooting the watermaker and getting ready to sail north for the summer, Robin and I found time to enjoy a sunset cruise aboard the Schooner Hindu. Schooner Hindu is a lovingly restored and historically significant 1925 gaff-rigged schooner with a rich maritime history. It sails out of Provincetown, MA in the summer, and Key West in the winter. Captain Josh sailed us right past Arabella, giving us a unique perspective on our own gaff-rigged wooden sailboat!
But, back to boat maintenance…
Installing the rudder feedback sensor presented a new challenge. It’s incredible how much I needed to deconstruct just to get that installed properly.
Now, mounting the bracket for the auto helm. The bracket is made of anodized aluminum, which gets mounted to a stainless bracket with stainless steel boats. That means I need to isolate and protect the bracket from corrosion. I chose to use Tef-Gel, which is a corrosion eliminator. The other important consideration is that, if we were to lose the bolts, there’s a good chance we would also lose the auto helm. As a backup, I drilled small holes into each bolt, where I can thread a ring through to prevent the bolts from working their way out.
Now that the above-deck electronics for the auto helm are hooked up, it’s time to go down below and get the system wired and set up down there. The Garmin Reactor 40 needs to be mounted near the center of the boat. This device gives us information about how the boat is moving in space and time.
Now, the auto helm came with a 40 amp breaker—but that didn’t fit into our breaker panel. After speaking with a marine electrician, I feel confident that a 20 amp breaker will do the trick just fine. With this final piece in place, we’re ready to test the auto helm under sail!
Unfortunately…more technical difficulties.
Somehow, installing the auto helm threw off the header sensor and wind reader. Fortunately, our marine electrician friend, Bob, might be able to help…
In the meantime, I took the chance to work on a small project: building a screen drop board to use when it’s hot and buggy. Our acrylic drop board is great, but it doesn’t help much with ventilation—and it’s getting HOT down here in the Keys. I drafted up a shopping list and hit the bricks for a walk to the hardware store, and fun, low-stress, no-surprises project for a change!
————————–
Sign up for our email newsletter: http://eepurl.com/hn3Qyv
Acorn to Arabella started as a wooden boat building project in Granby, Massachusetts. Steve began the journey as an amateur wooden boat builder crafting a 38′ wooden sailboat in his backyard: designer William Atkin’s Ingrid with a Stormy Petrel’s gaff rig. These videos follow the journey from tree felling, to lumber milling, to lofting, to the lead keel pour and now sailing the boat—sharing details of the woodworking, carpentry, metal smithing, tool building, and tool maintenance that traditional wooden boats command. This ultimate DIY project continues beyond the boat shop, as Steve and crew travel and learn to cruise aboard the handmade wooden boat that they’ve built. Just kidding about all that, this channel is about a Siberian Laika named Akiva.
————————–
If you are interested in supporting/helping here are a few ways:
https://www.acorntoarabella.com/how-to-help
Acorn to Arabella’s wishlist:
https://www.acorntoarabella.com/wishlistpriority
TotalBoat supports A2A! Please consider using our Total Boat referral code. Click here, then shop: https://www.totalboat.com/acorntoarabella They’ll kick 10% our way!
To offer recurring support via Patreon, CLICK BELOW. Just $5 a month gets you an invite to our monthly patron-only livestream Q&A sessions!
https://www.patreon.com/acorntoarabella
Original Soundtrack available at benfundis.bandcamp.com
FOLLOW US:
Patreon: https://www.patreon.com/acorntoarabella
Instagram: https://www.instagram.com/acorntoarabella/
Facebook: https://www.facebook.com/acorntoarabella
Website: http://www.acorntoarabella.com
Latest Episodes from Acorn To Arabella
Explore the most recent voyages. Subscribe to the channel to never miss an update!
A Quick Update From Ben
Check out this link and help in the fight against cancer. 100% of all funds raised go directly to research and patient care at Dana Farber.
saying-goodbye-to-rock-climbing-in-newfoundland
One last goodbye to a place that became so much more than another stop on the map 🇨🇦 Newfoundland gave us wild coastlines, big adventures, new friendships, and a whole lot of memories we’ll be carrying south with us. It’s hard to leave. But something tells us this isn’t goodbye forever. Thanks fo...
Saying Goodbye to Newfoundland—and the Man Who Inspired Arabella
After nearly a year in Canadian waters, it's finally time for Arabella to say goodbye to Newfoundland and begin the long journey south. But there is still one adventure left. Steve returns to the Nuddick for a final attempt at establishing a new multi-pitch climbing route, this time with his l...
Boat Work & Big Walls | Expedition Life #Shorts #ExploreCanada
Developing a new climbing route isn't just about climbing. It's hauling gear, improving the boat, making the route safer, and solving one problem after another. Every project brings us one step closer to establishing a new first ascent on Newfoundland's remote south coast. 👉 Watch t...
Upgrading the Rudder and Another Trek To The Cliff
After 3 years of service Steve makes a big change to the rudder head taking off the bronze hardware and replacing it with a more traditional wooden setup. Not too much bronze has been removed from Arabella (fortunately!), but this change will make steering much more pleasant. Then the crew makes o...