Sven Yrvind – Page 48

Watch Sven Yrvind Latest videos

Showing 1129-1152 of 1596 results
15 September 2022 More about the lid for deckhatches.
Sven Yrvind
15 September 2022 More about the lid for deckhatches.
The lid is a bit more delicate because it have to mate with the gasket and there is a bit of estimating to do as the lid is a composite product with an inner and outer skin. Those join each other and form a lip that closes against the gasket. I will do mor...
  • Sep 15, 2022
  • Language: EN
  • Play Time: 00:06:32
14 September 22022. Glassfibre on the rim, now comes a defelctor, holder for hand and mosquito net.
Sven Yrvind
14 September 22022. Glassfibre on the rim, now comes a defelctor, holder for hand and mosquito net.
The rim is now succesfully laminated with many pieces of glassfibre in and outside. Everything was covered with peel ply to get a good surface. Mow I put a rope on the outside wetted in NM-epoxy. Its function is to act as a deflector for water also to atta...
  • Sep 14, 2022
  • Language: EN
  • Play Time: 00:02:56
13 September 2022. Testing waterproof of hatches and stability range on two previus boats. Its fine.
Sven Yrvind
13 September 2022. Testing waterproof of hatches and stability range on two previus boats. Its fine.
Here is some videos from before that a friend helped me made. See also: yrvind.com for much more about my boats, voyages and adventures. If you’re interested in contributing links are below. https://www.paypal.com/donate?hosted_button_id=2MYSYADM4594Q Sw...
  • Sep 13, 2022
  • Language: EN
  • Play Time: 00:07:07
12 September 2022 An other small step on the outside of the coaming. Not much.
Sven Yrvind
12 September 2022 An other small step on the outside of the coaming. Not much.
I am now shaping the coamings. Working without a mould using sandwich construction means that each bit have to be shaped by hand. To get a goood result I chose to do it in several steps. There are commercial hatches for ocean goaing boats but they have sev...
  • Sep 12, 2022
  • Language: EN
  • Play Time: 00:00:38
11 September 2022. Laminating the inside of the hatch coamings.
Sven Yrvind
11 September 2022. Laminating the inside of the hatch coamings.
Today I have been laminating the inside of the coamings. The surfaces have compund curvature. That takes longer time. The good thing is that I did not have to worry about leisure. See also: yrvind.com for much more about my boats, voyages and adventures. I...
  • Sep 11, 2022
  • Language: EN
  • Play Time: 00:00:41
10 September 2022. The bottom part of the inner coaming is now shaped ready to take the glassfibre.
Sven Yrvind
10 September 2022. The bottom part of the inner coaming is now shaped ready to take the glassfibre.
I have now shaped the bottom of the inner coaming. It is the best starting as the top will get close to the hatch. See also: yrvind.com for much more about my boats, voyages and adventures. If you’re interested in contributing links are below. https://ww...
  • Sep 10, 2022
  • Language: EN
  • Play Time: 00:00:43
9 September 2022. From octagon to hexadecagon by wedges.
Sven Yrvind
9 September 2022. From octagon to hexadecagon by wedges.
Now I have glued 8 wedges on each hatch bringing the octagon to hexadecagon. This is on the inside. The outer side will rounded to approximate a circel. The main reason for the wedges is to make the thermal bridge longer. Condensation on a small boat with...
  • Sep 09, 2022
  • Language: EN
  • Play Time: 00:00:49
8 September 2022. Four more pieces on each deck hatch. Later an additional wedge completes the core.
Sven Yrvind
8 September 2022. Four more pieces on each deck hatch. Later an additional wedge completes the core.
One more step on the inner coaming is completed. A wedge in the inner corners of the inner coaming will shorten lengt of the cold bridges or themal bypasses created by the epoxy joints. That will reduce condensation when sailing in high latitudes. See also...
  • Sep 08, 2022
  • Language: EN
  • Play Time: 00:00:37
7 September 2022 First step on the deeck hatches.
Sven Yrvind
7 September 2022 First step on the deeck hatches.
Here is the first step on the deck hatches. To make easy I divide work in small steps. Also considering lithium batterys, they seam to involve a lot of more complicated electronics like regulators and one commentator wrote that I had to use a bus. Now I do...
  • Sep 07, 2022
  • Language: EN
  • Play Time: 00:01:04
6 September 2022. Reconsidering litium batteries. Will be cautius and get myself informed. + Bonus.
Sven Yrvind
6 September 2022. Reconsidering litium batteries. Will be cautius and get myself informed. + Bonus.
There have been many comments on the 5 September video on how absolutly safe the Lithium Iron Phosphate (LiFePo4) are. I am still sceptical. I had planned to get my batterys now but what I will do is to wait. Maybee I can do sea trials next year 2023. Duri...
  • Sep 06, 2022
  • Language: EN
  • Play Time: 00:05:02
5 September 2022 How to solve it The oar and the solar panels wants the same space.
Sven Yrvind
5 September 2022 How to solve it The oar and the solar panels wants the same space.
In general, not only on boats there is a fight for the same place. Things interfere with each other. Here I solved it by making a grove below the solar panels for the oar. Its a good place for it much more better than on the previus boat. A bounus is that ...
  • Sep 05, 2022
  • Language: EN
  • Play Time: 00:06:16
4 September 2022. Mock up for the diameter of the round deck hatches.
Sven Yrvind
4 September 2022. Mock up for the diameter of the round deck hatches.
Today I try out the diameter for the deck hatches. It is a balance. In port and in good weather and in warm clomates it is very desirable to have big deck openings. The intended cruising ground for my boat ranges from the equator to the high latitudes. I ...
  • Sep 04, 2022
  • Language: EN
  • Play Time: 00:03:17
3 September 2022. Today I reinforced the lower part of the starbord mast holder.
Sven Yrvind
3 September 2022. Today I reinforced the lower part of the starbord mast holder.
Now the bottom part of the two mast holders are strong. Nex step? I will think a bit before deciding. See also: yrvind.com for much more about my boats, voyages and adventures. If you’re interested in contributing links are below. https://www.paypal.com/...
  • Sep 03, 2022
  • Language: EN
  • Play Time: 00:00:46
2 September Anchoring the lower part of the port mast holder to the boat.
Sven Yrvind
2 September Anchoring the lower part of the port mast holder to the boat.
It is the ends of the mast holder thats doing the holding. The middle part is just their to orient the ends. It is the ends that have to be strong. Here I make the lower part strong with 3 extra 450 gram glas in NM-epoxy. See also: yrvind.com for much more...
  • Sep 02, 2022
  • Language: EN
  • Play Time: 00:01:43
1 September 2022. Gluing the mastholder in position.
Sven Yrvind
1 September 2022. Gluing the mastholder in position.
The two mastholder is now fixed in their final position with plenty of NM-epoxy and thickener. Later it is going to be made more stong with glassfiber. See also: yrvind.com for much more about my boats, voyages and adventures. If you’re interested in con...
  • Sep 01, 2022
  • Language: EN
  • Play Time: 00:01:31
31 August 2022 Making the bottom of the mast holders stronger.
Sven Yrvind
31 August 2022 Making the bottom of the mast holders stronger.
This is just a small step. I am making the bottom of the mastholders stronger. The top strong point will be at deck level and will by its nature, having a very large diameter be very strong. Much stronger than the mast anywhay. See also: yrvind.com for muc...
  • Aug 31, 2022
  • Language: EN
  • Play Time: 00:01:22
30 August 2022 Details of the mastholder, the bottom part.
Sven Yrvind
30 August 2022 Details of the mastholder, the bottom part.
Here are details of the mastholders bottom part. A kind of vedge is at the hull side to get the desired 11° outward angle to the masts. Also I have added a bottom consisting of 10 mm Tufnol. Mow the mastholder are ready to be glued to the corner of the hu...
  • Aug 30, 2022
  • Language: EN
  • Play Time: 00:02:26
29 August 2022. Why a longer boat makes less resistance than a shorter if displacement is the same.
Sven Yrvind
29 August 2022. Why a longer boat makes less resistance than a shorter if displacement is the same.
Racing boats are prestigius thats why builders of production boats copy them. But racing boats are limited by rules and regulation especially concerning speed. In other words the speed of a racing boat is limeted by racing rules. Cruising boats are not rac...
  • Aug 29, 2022
  • Language: EN
  • Play Time: 00:04:50
28 August 2022 The second mast holder Fine Positioning them and making bulkhead 20 mm higher.
Sven Yrvind
28 August 2022 The second mast holder Fine Positioning them and making bulkhead 20 mm higher.
This method of wrapping the male mold in plastic film is excellent fast and quick release. If you want a shiny surface its not for you. If however you are a 60 grit man like me. Go for it. The second mast holder came out as easy as the first one. Now I am...
  • Aug 28, 2022
  • Language: EN
  • Play Time: 00:03:40
27 Aug 2022. The second mastholder is now laminated. Everything well.
Sven Yrvind
27 Aug 2022. The second mastholder is now laminated. Everything well.
I had been worried about etting the first mastholder out of the mold. There was releise angle only at one way. Lenghtwise the sides was parrallel. Not a good a good condition. It really went so easy that I did not even have to use force. Today doing the se...
  • Aug 27, 2022
  • Language: EN
  • Play Time: 00:01:34
26 August 2022 Laminating the first mastholder.
Sven Yrvind
26 August 2022 Laminating the first mastholder.
I was apprehensive about the laminating of the first mastholder. There was several ways of doing it. One idea was to have her horisontal and turn as I did laminate. Gravity would temporarily help. An other way was to have her standing vertical. Gravity wou...
  • Aug 26, 2022
  • Language: EN
  • Play Time: 00:01:39
25 August 2022 Warm wool socks and trying to fix a problem on the mold for the mast holder.
Sven Yrvind
25 August 2022 Warm wool socks and trying to fix a problem on the mold for the mast holder.
I did only roughen up the PVC close to the wood/ PVC joint. That was a mistake. The epoxy did not adhere well to the part of the PVC not sandpapered. The glassfibre liked to peel of. I may have saved it by wrapping the hole thing in glassfibre. Tomorrow we...
  • Aug 25, 2022
  • Language: EN
  • Play Time: 00:03:20
24 August 2022. Making the mold for the mastholder using a 75 mm diameter PVC pipe and plywood
Sven Yrvind
24 August 2022. Making the mold for the mastholder using a 75 mm diameter PVC pipe and plywood
Here is a bit of my thinking making the mold for the mastholder. It will be made of glass and carbonfibre. It is an experiment. We will see how it works out. See also: yrvind.com for much more. If you’re interested in contributing links are below. https:...
  • Aug 24, 2022
  • Language: EN
  • Play Time: 00:03:56
23 August 2022. Interference made me change from ackommodation work to mast holder work Cest la vie.
Sven Yrvind
23 August 2022. Interference made me change from ackommodation work to mast holder work Cest la vie.
I like to thank everyone for the kind donations. They are truly appriciated. They give me the means to continue to build and do short videos. When I had finished the centerboard to my satisfactine and that had taken some time. I told myself now I will stra...
  • Aug 23, 2022
  • Language: EN
  • Play Time: 00:02:34

Something AWESOME is coming!
Be the FIRST to know⛵

Sign up for exclusive updates and be the first to hear when we go live!
Get sneak peeks, exciting announcement, and special content straight to your inbox!

We don’t spam! Read our privacy policy for more info.


WeBoating
Logo
Shopping cart