Cerbo GX, Anchor Buoy and Hose Fixes | Boat Jobs & Fixes 02

Dean and Anne-Lill tackle three essential maintenance jobs aboard their Bali 4.6 catamaran, setting up Victron Cerbo GX tank monitoring, fabricating an anchor marker buoy, and plumbing an anchor locker washdown hose.

Cruising the Mediterranean aboard their Bali 4.6 catamaran, Dean and Anne-Lill undertake three practical maintenance projects to improve deck handling and electrical monitoring. Documenting their journey aboard Sailing Queen Lizzy, the Australian couple focuses on protecting ground tackle in crowded anchorages, organizing chain washdown gear at the bow, and integrating tank telemetry into a centralized Victron Cerbo GX processor.

Anchor Marker Buoy Fabrication and Deployment

In busy Mediterranean anchorages, crossing anchor chains presents a continuous operational hazard. While the crew relies on GPS data and a PredictWind DataHub Pro anchor alert on the boat to track their position, that system does not indicate to nearby vessels where Queen Lizzy’s ground tackle lies. Commercial auto-retrieving anchor buoys like Mobius offer a solution, but Dean notes they cost 500 to 1,000 Euro and remain vulnerable to being run over and cut by passing boats.

To safeguard their tackle affordably, the crew fabricates a custom anchor warning marker. Anne-Lill inflates the buoy using their onboard air compressor while Dean splices high-visibility line. The setup uses an elastic bungee stretching 4 to 5 meters that clips to the crown of the anchor. Spliced loops placed at intervals allow depth adjustments. In 10 meters of water, the line hooks to a loop placed at 5 meters along the lead, keeping the buoy positioned directly over the anchor. As Dean explains, the marker gives nearby mariners a clear visual cue: “Don’t drop your anchor on top of ours.” During retrieval, the line stays clipped to the anchor crown and is hauled back aboard.

Saltwater Chain Washdown Installation

Retrieving ground tackle often brings up sticky mud and salt sediment over the chain and bridles. Queen Lizzy featured a saltwater washdown pump connection at the forward crossbeam, but lacked a dedicated stowage hook and hose assembly inside the anchor locker. Routine recovery required messy handling or hauling buckets on deck.

To organize the locker, the crew visited a marine chandlery to acquire a longer stainless steel hook. Dean positions the hook high on the internal bulkhead so Anne-Lill can pull the hose out quickly without reaching deep into the locker bilge. Before drilling into the composite, Dean safeguards the bulkhead: “The old trick of putting a little bit of tape on the drill itself or drill bit itself so we don’t drill in too far.” With the hook bolted firmly in place, the coiled hose hangs neatly above the chain pile, ready for immediate rinsing during windlass operation.

Cerbo GX Marine Backbone and Tank Telemetry

The central technical upgrade addresses Queen Lizzy’s tank sensors and electrical telemetry. From the factory, the catamaran came equipped with an analog Schreiber display. Dean found the factory setup severely lacking, noting that “because the system that comes with the Bali, the Schreiber system is very poor in in what it provides in information.” The factory gauges offered zero monitoring for the black water holding tanks. Refilling diesel was also an awkward two-person task: one person stood at the aft deck filling port while another waited inside the salon watching the gauge and shouting when the volume approached 100%.

Dean mounts a Victron Cerbo GX communication hub to unite the vessel’s Victron inverter, MPPT solar charge controllers, and tank senders onto the NMEA marine electronics backbone. The Cerbo GX base unit provides an 8-wire connector terminal block capable of reading 4 tanks directly. To ensure solid electrical connections, Dean avoids pushing bare stranded copper directly into terminal pins. Instead, he inserts each wire into a metal ferrule and clamps it down with a ferrule clamping tool to eliminate fraying and short circuits.

To expand capacity for the catamaran’s 2 black water tanks, Dean plans to add a GX 140 extension box. Accessing the tight machinery void behind the port aft shower panel, Dean cuts the original Schreiber sensor leads and splices in new multi-conductor signal cables. Dean then routes the wiring beneath cabin floorboards, running lines across both engine bays and into the opposite hull to link freshwater, diesel, and black water tanks to the central display. Working through tight bilges, Anne-Lill teases him about practicing boat yoga, to which Dean cheerfully responds, “And loving it.”

Equipment Specifications and Installation Data

The following table summarizes the specifications, components, and measurements utilized across the three deck and electrical projects:

Component or taskSpecification or measurementApplication on vessel
Anchor buoy bungee4 to 5 meters stretchedElastic lead clipped to anchor crown for 10-meter anchoring depths
Commercial buoy option500 to 1,000 EuroEstimated cost of commercial retrieval markers like Mobius
Cerbo GX tank connector8 wires with clamped ferrulesTerminal block monitoring 4 onboard tanks without shorting
Auxiliary expansion boxGX 140Extension unit dedicated to reading the 2 black water holding tanks

Centralized System Visibility

With the wiring routed and the Cerbo GX connected to the NMEA network, the crew can monitor battery status, tank levels, and temperatures from helm multifunction displays or mobile apps anywhere aboard. Refueling diesel tanks becomes an efficient solo task, with real-time level percentages visible directly on mobile screens at the fuel dock. As Anne-Lill observes of the integrated instrumentation, “We can’t stop things breaking but we can see them coming.” By combining physical deck upgrades with digital monitoring, Dean and Anne-Lill leave Queen Lizzy better prepared for Mediterranean cruising.

Frequently Asked Questions

Why did the crew install an anchor buoy on Queen Lizzy?

Anne-Lill and Dean installed an anchor buoy to give other boaters a clear visual marker directly above their ground tackle, preventing nearby vessels from dropping anchor across their chain in crowded Mediterranean anchorages.

How does the DIY anchor marker line adapt to varying depths?

The buoy system utilizes an elastic bungee line stretching 4 to 5 meters clipped to the anchor crown, paired with spliced rope loops placed at intervals such as 5 meters for anchoring in 10 meters of water.

Why did the crew replace the factory Schreiber tank monitoring panel?

The factory Schreiber display provided poor information and lacked black water tank level readouts, while also requiring someone inside the cabin to yell out fuel levels when refilling diesel tanks toward 100%.

Why does Dean use wire ferrules when wiring the Victron Cerbo GX?

Dean uses wire ferrules and a ferrule clamping tool on the 8-wire connector block to prevent stranded copper wires from fraying, loosening, or shorting between adjacent terminal pins.

What onboard equipment integrates into the Victron Cerbo GX system?

The Victron Cerbo GX links the vessel’s Victron inverter, MPPT solar charge controllers, and 4 tank senders into the NMEA marine electronics backbone, with a GX 140 extension planned for 2 black water tanks.

Book a trip where this was filmed — near Tuscany

See all 17 experiences in Tuscany →

Support Sailing Queen Lizzy

At WeBoating.com, we profoundly acknowledge the unwavering dedication that Sailing Queen Lizzy invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.

We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.

We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "Cerbo GX, Anchor Buoy and Hose Fixes | Boat Jobs & Fixes 02" video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Sailing Queen Lizzy, their collaborators, and the brands they're associated with.

To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.

If you have any feedback, corrections, or additional information about Sailing Queen Lizzy or their videos, please use the comment form below to share your thoughts with us.

Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!

Installing an anchor buoy, fixing an anchor locker hose and setting up Victron Cerbo GX tank monitoring: three boat jobs on our Bali 4.6 catamaran. Sailing Queen Lizzy — liveaboard life aboard our Bali 4.6 catamaran in the Mediterranean.

We’re Anne-Lill and Dean, an Australian couple sailing our Bali 4.6 catamaran across the Mediterranean — slowly building toward the big one: an offshore passage through French Polynesia and maybe home to Sydney. Real liveaboard life, no filter, no fluff.

This is the jobs episode. We put a buoy on the anchor, deal with a hose in the anchor locker, and set up a Victron Cerbo GX. The Cerbo means we can finally see the black water tanks, which we couldn’t before. Every job went in.

There’s always another locker.

We’re Australian, we probably should have known better, and we are fixing it ourselves anyway. Come along for all of it — the harbours, the headlands and the long blue days.

🔔 Subscribe and come sail with us, one mile at a time:
https://www.youtube.com/@SailingQueenLizzy?sub_confirmation=1

⛵ Boat: Bali 4.6 Catamaran
🌍 Location: The Mediterranean Sea

Chapters
00:00 Intro
00:15 Job 1: Anchor buoy
03:37 Job 2: Anchor locker hose
06:14 Job 3: Cerbo GX monitoring
10:52 Jobs done!

📘 Facebook: https://www.facebook.com/sailing.queen.lizzy/
📸 Instagram: https://www.instagram.com/sailingqueenlizzy

#SailingQueenLizzy #sailing #catamaran #liveaboard #Bali46

Cerbo GX, Anchor Buoy and Hose Fixes | Boat Jobs & Fixes 02 Location

  • Porto Azzurro, Elba, Italy (42.7667,10.3981)
We will be happy to hear your thoughts

Leave a reply


Latest Episodes from Sailing Queen Lizzy

Explore the most recent voyages. Subscribe to the channel to never miss an update!

Showing 1-6 of 60 results
Please don’t anchor on top of us ⚓ #shorts
Sailing Queen Lizzy

Please don’t anchor on top of us ⚓ #shorts

Three boat jobs and one very small crawl space. First up, an anchor buoy. It floats above our anchor so the next boat can see exactly where it is and has no excuse for dropping theirs on top. The ones you can buy were 500 to 1000 euro, so we made our own. Then a hose for the anchor locker, and a s...
Bird Poo, Choice Words, Then Just Wind #Shorts
Sailing Queen Lizzy

Bird Poo, Choice Words, Then Just Wind #Shorts

Leaving Porto Venere under sail: a hose-down, the Code 0 going up, and no engines all day. 👉 Watch the full episode: Sailing Queen Lizzy — liveaboard life aboard our Bali 4.6 catamaran in the Mediterranean. 🔔 Subscribe: #Shorts #sailing #catamaran #SailingQueenLizzy
Our Glorious First Day on Elba #Shorts
Sailing Queen Lizzy

Our Glorious First Day on Elba #Shorts

Arriving off the headland of Elba, the crew prepares to drop anchor, spots a tall ship in the harbor, and takes the tender ashore to explore local markets and waterfront streets.
Five Villages. One Coastline. One Day. #Shorts
Sailing Queen Lizzy

Five Villages. One Coastline. One Day. #Shorts

Cinque Terre in one day. Five villages, one coastline, and we're having a go anyway. 👉 Watch the full episode: Sailing Queen Lizzy — liveaboard life aboard our Bali 4.6 catamaran in the Mediterranean. 🔔 Subscribe: #Shorts #sailing #catamaran #SailingQueenLizzy
Cerbo GX, Anchor Buoy and Hose Fixes | Boat Jobs & Fixes 02
Sailing Queen Lizzy

Cerbo GX, Anchor Buoy and Hose Fixes | Boat Jobs & Fixes 02

Dean and Anne-Lill tackle three essential maintenance jobs aboard their Bali 4.6 catamaran, setting up Victron Cerbo GX tank monitoring, fabricating an anchor marker buoy, and plumbing an anchor locker washdown hose.
A Break From the Boat Jobs, classic cars in Tuscany
Sailing Queen Lizzy

A Break From the Boat Jobs, classic cars in Tuscany

A break from the boat jobs: a classic car rally in Tuscany, a Lamborghini on the road ahead and a wine cellar in Gaiole in Chianti. 👉 Watch the full episode: Sailing Queen Lizzy — liveaboard life aboard our Bali 4.6 catamaran in the Mediterranean. 🔔 Subscribe: #Shorts #sailing #catamaran #Saili...
Browse All Videos
WeBoating
Logo
Shopping cart