Episode 326 - Hour Special - Boat Work & Beach Days!

Chris and Nicky of Sailing Pickle Family push through tricky gel-coating and non-slip deck work in Spain before testing a new tender engine and celebrating Bo's boat purchase.

In the Spanish marina where their catamaran Pickle is docked, Chris and Nicky of the Sailing Pickle Family tackle day two of cockpit gel-coating before escaping to the coast with their son Bear. Working within the helm station, Chris concentrates on recoating the steering column and console faces while Nicky manages interior duties. Cooler ambient temperatures around 23 to 24 degrees complicate the chemical cure, as a cautious 1 percent catalyst ratio leaves wet resin sagging into drips and runs that take 45 minutes to tack off. Recognizing that cooler weather requires more catalyst, Chris bumps the hardener to 2 percent on subsequent coats to cover the engine box and surround surfaces.

With the boat cockpit consoles finished in fresh white, refit priorities shift toward the removable cockpit floorboards that require durable non-slip traction. Rather than working outdoors exposed to changing weather, the crew secures indoor space to complete the chemical work under cover.

Steering Console Gel Coating and Catalyst Ratios

Applying gel coat inside the cockpit requires constant adjustments to fluctuating temperatures. Chris discovers that the 1 percent hardener mixture he initially mixed takes far too long to set in the morning air. Staring at resin runs on the console faces, he waits out the cure before applying a heavier mix.

Increasing the catalyst to 2 percent on the engine cover accelerates the process, allowing Chris to complete two successive coats. Although the resin remains slow to harden in the cooler temperatures, the helm console surfaces and surrounding trim are successfully brought back to a clean white finish. Chris notes that once the floorboards are prepped and completed, the labor-intensive chore of sanding the entire cockpit structure can finally begin.

Thunderstorms and Hangar Non-Slip Floorboards

As rain begins falling across the yard, Chris and Nicky move their floorboard project into an empty boatyard hangar. Local yard workers permit them to occupy a broad indoor floor space, where the couple lays out cardboard sheets to protect their work from falling dust. Outside, lightning and heavy thunderstorm downpours sweep through the coast, validating Nicky’s remark: “Rainy day in Spain. Very rainy.”

The project encounters early logistical hurdles when Chris realizes he left one of the cockpit floorboards behind in their vehicle, followed immediately by another walk through the rain after discovering he forgot the silica additive. To formulate the non-slip coating, Nicky measures out “Eight heaped tablespoon of silica” into the gel coat alongside a 2 percent catalyst mixture. Because the cold weather prevents the resin from holding sharp peaks, they apply the thick mixture across seven or eight cockpit floorboards using specialized tools, as Nicky explains: “These textured like Artexing rollers to put on the second coat.” The damp atmosphere stretches curing time to 2 hours, forcing the crew to leave the coated boards inside the hangar over the weekend.

Bo’s Project Yacht and Buddy’s Pontoon Escape

With the cockpit floorboards safely curing, Nicky reveals major news regarding their seventeen-year-old daughter Bo. Working hard through a summer job, Bo saved enough money to purchase her own classic vessel on the Isle of Scilly, prompting Nicky’s proud announcement: “She works a summer job, earned 300 quid. She spent on a boat.” The vessel, a 28-foot Westerly monohull, requires significant hands-on refit work including replacement windows, a bilge pump, and starter motor overhaul before the family visits her at Christmas.

Back at the catamaran, an unexpected scare interrupts morning preparations. While Chris works on electrical plugs and removes the boarding gangway, Buddy, the family dog, wanders down the ramp unnoticed. Buddy roams the marina pontoon alone for 10 to 15 minutes before returning faithfully to the dock edge, waiting patiently outside Pickle’s hull to be welcomed back aboard.

Tool Breakdowns and Cockpit Sanding Roadblocks

While Nicky accompanies Bear to the beach for his prescribed daily break from his spinal brace, Chris remains on Pickle to begin sanding the cockpit gel coat. The maintenance plan hits a brick wall when their single orbital sander fails. The tool had suffered a broken trigger, caught fire after repairs, and now ceased working entirely after roughly three hours of use. A frustrated Chris reports: “Yet once again, the sander has broken. This is the third sander now.”

With replacement delivery unavailable for 3 days until Tuesday, all cockpit sanding grinds to a halt. The family pauses refit work to watch 100 runners pass the shoreline in a local marathon, before regrouping at an open tapas bar to enjoy food, drinks, and grande beers while discussing Bear’s ongoing physical recovery.

Tender Break-In, Flying Drones, and Cold August Waters

With boatyard sanding stalled, Nicky and Bear launch their new 3D Tender into coastal waters to complete mandatory engine break-in procedures. Observing the 3-knot marina speed limit, they set out to log an hour and 20 minutes under stage two of the engine running-in protocol. Nicky trims the outboard mounting angle to eliminate excess wake, instructing Bear on proper acceleration: “Needs to be on the plane, so there’s not too much stress on the engine.”

During the run, Bear successfully launches and catches his drone from the moving tender without incident. Cruising across water with 10 meters of visibility down to the sandy seabed, the pair spots drifting cone jellyfish and anchors to swim. Despite midsummer conditions, Nicky remarks: “I don’t think I have ever remember swimming in the Mediterranean water and it being this cold in August.” Nicky noticed warm surface patches where Bear dives using his electric water jet propulsion device, towing the tender behind him in the water. After clocking planning speeds where Bear observes: “I Googled it and it was 21.4 mph.” the crew heads back to the marina to wrap up an eventful week of boat work.

Refit Task or Project StageMeasurement or FigureRecorded Video Detail
Cockpit steering console1% to 2% catalyst mixRequired 45 minutes cure time at 23 to 24 degrees ambient temperature
Non-slip cockpit floorboards8 heaped tablespoons of silicaSpread across 8 boards using Artexing rollers with a 2-hour cure
Bo’s project yacht300 quid purchase price28-foot Westerly monohull purchased on Isle of Scilly by 17-year-old Bo
Cockpit orbital sanding3 hours run timeThird sander failure halted refit progress for 3 days until Tuesday
Tender outboard break-in2 hours stage two cycle1 hour and 20 minutes logged; planning speed recorded at 21.4 mph

Frequently Asked Questions

Why did the gel coat take longer to cure on the steering console?

Chris mixed the gel coat at a 1 percent catalyst ratio on a cooler 23 to 24 degree day, causing drips and runs that required 45 minutes to tack off before he increased the hardener to 2 percent.

How did Chris and Nicky apply non-slip texture to the cockpit floorboards?

They mixed 8 heaped tablespoons of silica powder into gel coat with a 2 percent hardener mix inside a boatyard hangar and applied it across 8 boards using textured Artexing rollers.

What kind of boat did Bo purchase for her refit project?

Bo purchased a 28-foot Westerly monohull yacht on the Isle of Scilly for 300 quid, which she earned from a summer job.

What mechanical issue halted cockpit sanding on Pickle?

Their Bosch Professional orbital sander broke down for the third time after about three hours of use, halting sanding work for 3 days while waiting on a replacement tool.

What procedures were required during the tender engine break-in?

The crew needed to log 2 hours at variable throttle under stage two of engine break-in, maintaining a 3-knot marina speed limit before bringing the boat onto the plane.

Book a trip where this was filmed — near Andalucia

Support Sailing Pickle Family

At WeBoating.com, we profoundly acknowledge the unwavering dedication that Sailing Pickle Family invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.

We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.

We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "Episode 326 - Hour Special - Boat Work & Beach Days!" video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Sailing Pickle Family, their collaborators, and the brands they're associated with.

To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.

If you have any feedback, corrections, or additional information about Sailing Pickle Family or their videos, please use the comment form below to share your thoughts with us.

Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!

Lots and lots of loose ends tied up this week, we finish lots of gel-coating jobs and finally start to sand the cockpit... we're all white again, Yay! And Bear and I share a few odd days escaping to gorgeous beaches and out on our new tender breaking in the engine while having loads of fun swimming, snorkelling and playing with Bear’s water jet! Such a fun week guys, happy to share it all with you!

Thank you to our wonderful patrons, you are really helping to make all this possible! Don't forget to pop over to Patreon to watch all the extra footage, and get all our episodes a week early. If you'd like to become part of the Patron Pickle Family please follow the link below and join all the fun, your help is massively appreciated!!

http://www.patreon.com/sailingpicklefamily

https://www.paypal.me/sailingpickle

http://www.sailingpicklefamily.co.uk

For all our very cool Merchandise head over to, https://sailing-pickle-family.myspreadshop.co.uk/

You can also find us at Facebook and Instagram;
http://www.facebook.com/sailingpicklefamily
http://www.faccebook.com/chris.sailingpickle.79

http://www.instagram.com/sailingpickle
http://www.instagram.com/chrissailingpickle
http://www.instagram.com/beaupickle

http://www.tiktok.com/@nickypiccalilli
http://www.tiktok.com/beaupickle
http://www.twitter.com/picklesailing

Our Graphic Designer: https://www.instagram.com/phx_65

Awesome Tenders! www.3dtender.com

Fantastic furling systems!! www.seldenmast.com

best knives! https://www.spyderco.com

Smaco e-scooter and dive tanks
https://smacodive.com/?ref=SailingPickleFamily


3D Immunity - Daily Defense Drink - 3D10%OFF/PICKLE
AFFILIATE LINK -
https://www.dailydefensedrink.com?sca_ref=7294578.7UtyRK2nVE

https://vagrant-gipsy.peachs.co/a/pickle


music from www.bensound.com/free-music-for-videos

Episode 326 - Hour Special - Boat Work & Beach Days! Location

  • Almerimar, Spain (36.6967,-2.7958)
We will be happy to hear your thoughts

Leave a reply


Latest Episodes from Sailing Pickle Family

Explore the most recent voyages. Subscribe to the channel to never miss an update!

Showing 1-6 of 380 results
Episode 326 – Hour Special – Boat Work & Beach Days!
Sailing Pickle Family

Episode 326 – Hour Special – Boat Work & Beach Days!

Chris and Nicky of Sailing Pickle Family push through tricky gel-coating and non-slip deck work in Spain before testing a new tender engine and celebrating Bo's boat purchase.
Episode 325  – No Steering on Our Catamaran!
Sailing Pickle Family

Episode 325 – No Steering on Our Catamaran!

Facing persistent helm slip on their 1982 Prout Snowgoose 35 catamaran Pickle, Nicky and Chris replace a failing helm pump, realign a bent steering ram, and apply fresh gelcoat across the cockpit in Mediterranean heat.
Episode 324 – European Road Trip… New Engine and New Boat!
Sailing Pickle Family

Episode 324 – European Road Trip… New Engine and New Boat!

After driving across Europe to rejoin their catamaran Pickle in Spain, the crew breaks in a new 15 hp tender outboard while Beau begins restoration work and window repairs on her newly acquired 28-foot sailboat Dubado.
Episode 323 – SV Dubado joins the Sailing Pickle Family!
Sailing Pickle Family

Episode 323 – SV Dubado joins the Sailing Pickle Family!

Beau introduces SV Dubado, a 28-foot Macwester sailboat joining the family fleet for winter renovation, while Bear tackles target shooting and pottery painting.
Episode 322 – Monsters and Demon Sailors!
Sailing Pickle Family

Episode 322 – Monsters and Demon Sailors!

The Sailing Pickle Family celebrates Bear turning thirteen with an action-packed UK itinerary, including monster trucks, homemade fudge cake, FPV drones, Southend arcades, and jellied eels.
Episode 321 – From Boat Adventures to Aeroplanes!
Sailing Pickle Family

Episode 321 – From Boat Adventures to Aeroplanes!

Nicky and Chris of Sailing Pickle Family celebrate son Bear's 13th birthday, trading their cruising catamaran Pickle for a hands-on aviation history tour in Lincolnshire, England.
Browse All Videos
WeBoating
Logo
Shopping cart