In the heat of Puerto Peñasco, Mexico, Jamie and Princess took on an extensive refit session aboard their aluminum catamaran Sailing Life on Jupiter. The workday combined messy interior upkeep with critical propulsion overhaul. While Princess stripped the sofa cushion covers to run them through the washing machine and scrubbed caked grease off the barbecue grill until the stainless steel resurfaced, Jamie and crewmate Bruce began tackling a decade-old alignment defect in the engine compartments.
Between laundry loads and oven cleaning, the crew weighed whether to keep the portable washing machine on board. Jamie had considered selling the machine in Mexico after discovering a replacement model that would fit the dedicated laundry area for their planned travels in French Polynesia. With no local buyers stepping forward, Jamie chose to retain the current unit, adding foam padding to the top and bottom to secure it inside the hull.
Taking a mandatory pause while waiting for engine mount adhesives to set, the crew rested inside the cabin under temporary air conditioning. Jamie had routed ducting directly into the cabin, relying on a simple cardboard baffle switch to direct the chilled airflow. The makeshift installation held up through rain and provided necessary relief from the heat in Mexico, making the living quarters manageable while mechanical work paused.
The break yielded an unexpected discovery when Princess began searching through the center bilge. Rather than a dropped tool or mechanical problem, Princess uncovered a forgotten stash of two dozen beers from Panama buried beneath the floorboards. The find brought immediate laughter from the crew, who celebrated the coincidence of uncovering cold Panama beers since Jamie and Princess first met in Panama years earlier. Toasting with the rediscovered cans, the crew joked about dubbing the batch “bilge beer” before preparing for the next phase of heavy mechanical work in the hulls.
The primary mechanical objective focused on replacing four failing rubber engine mounts beneath the diesel engine. The work on the first engine consumed most of a full day, though overcast skies offered welcome protection from the brutal heat. Upon unbolting the assembly, Jamie identified a persistent manufacturing flaw that had plagued the catamaran since construction.
“Two of the engine mounts were like leaning for 10 years. And now we just filed out Bruce filed out with a Dremel a little bit more athwartships movement, and now they’re standing vertically.”
Because the original mounting studs penetrated fixed brackets without adequate lateral clearance, the mounts had remained cocked at an angle, accelerating rubber degradation much like driving on an unbalanced vehicle tire. Using a rotary Dremel tool, Bruce elongated the bracket holes athwartships, providing sufficient clearance for the new mounts to stand upright and absorb engine vibration properly. The only setback occurred during disassembly when a throttle linkage attachment snapped, leaving Jamie with an additional repair before the engine could be commissioned.
When transitioning to the second engine, Jamie applied lessons learned from the previous day to dramatically improve efficiency. Rather than wrestling the heavy engine by hand within the cramped compartment, Jamie devised a lifting rig using a structural crossbeam laid across the companionway hatch.
“The win was using a beam across the hatchway. Use the main sheet as a five purchase block and tackle straight up to the sheet winch.”
Connecting the mainsheet tackle directly to the sheet winch allowed Jamie to hoist the engine clear of its mounting lip with just three or four rotations of the winch handle. The entire procedure on the second engine was completed in only 1 and 1/2 hours.
Before securing the new hardware, Jamie coated every bolt thoroughly in Tef-Gel anti-seize paste to prevent galvanic corrosion between stainless steel fasteners and the aluminum vessel structure.
“Trying to avoid corrosion. This is This is what it’s all about now. I think I’ve learned my lesson.”
Jamie highlighted the long-term economy of the isolation compound, pointing out that his 100-dollar container of Tef-Gel had lasted 15 years since purchase and remained useful for protecting metal threads in marine environments.
With mechanical lifting concluded, the crew returned to the saloon to finish reassembling the interior cushions. Wrestling dense foam blocks back into freshly laundered fabric covers required substantial physical effort, but the finished living space earned immediate praise from young Oakley.
Attention then turned to the propeller shaft assembly and stern gland. Jamie inspected the dripless shaft seal installed on the boat, explaining the custom design developed by catamaran builder Tim Mumby.
“Tim Mumby builds these just by using a couple of diameters of exhaust hose and some oil seal. Perfectly dry bilge. And it costs about 50 bucks to make instead of 500 bucks for one from the shop.”
Jamie noted that commercial mechanical face seals often rely on delicate internal springs and thin rubber bellows that can perish quickly, posing a serious risk of catastrophic flooding. The Mumby design relies on rugged exhaust hose and industrial oil seals to guarantee a dry bilge at a fraction of the cost.
Rebuilding the starboard seal required addressing a broken cooling water feed fitting where water from the exhaust elbow injects into the stern bearing to provide lubrication. Jamie planned to repair the junction, slide the propeller shaft home, and align the shaft couplings using feeler gauges. Final commissioning tasks outlined for the propulsion system included mending the broken throttle arm, draining 3-year-old diesel fuel from the tanks, fitting fresh fuel filters and engine fluids, and refurbishing the mounting bracket for the 800 PSI watermaker high-pressure pump.
| Maintenance task | Metric or hardware detail | Refit application on Jupiter² |
|---|---|---|
| Engine mount alignment | 10 years | Eliminated athwartships lean present since vessel construction |
| Engine mount replacement | 4 mounts per engine | Replaced degraded rubber vibration isolators on both diesels |
| Second engine swap time | 1 and 1/2 hours | Hoisted engine clear using 5-purchase mainsheet tackle to sheet winch |
| Fastener barrier paste | $100 container | Applied Tef-Gel compound purchased 15 years prior to stop galvanic corrosion |
| Tim Mumby dripless shaft seal | $50 DIY cost | Built with exhaust hose and oil seals, replacing $500 commercial seal |
| Stagnant fuel replacement | 3 years | Draining old fuel from tanks alongside new filters and fluids |
| Watermaker pump maintenance | 800 PSI | Refurbishing mounting bracket for high-pressure reverse osmosis pump |
Two of the engine mounts had been leaning askew athwartships for 10 years since the catamaran was built, causing accelerated wear similar to driving on an unbalanced tire. Bruce used a Dremel tool to file out additional athwartships clearance so the mounts could stand vertically.
Jamie spanned a support beam across the companionway hatch and rigged the mainsheet as a 5-purchase block and tackle connected to the sheet winch. Hoisting the engine clear of its mounting lip took three or four turns of the winch handle.
After spending most of a day refining the procedure on the first engine, Jamie completed the engine mount replacement on the second engine in 1 and 1/2 hours using the overhead beam and mainsheet tackle.
Jamie coated the fasteners with Tef-Gel anti-corrosion paste, noting that he purchased the 100-dollar container 15 years earlier to protect metal threads on the aluminum catamaran.
The custom dripless seal designed by Tim Mumby uses multiple diameters of exhaust hose and oil seals lubricated by cooling water from the exhaust elbow. It costs approximately $50 to build, avoiding the fragile springs and deteriorating bellows of $500 commercial seals.
Princess found a hidden cache of two dozen beers from Panama buried in the center bilge, a fitting discovery since Jamie and Princess first met in Panama.
At WeBoating.com, we profoundly acknowledge the unwavering dedication that Sailing Life on Jupiter invests in crafting each and every video or voyage. Their passion for delivering exceptional ocean content shines through every frame, and it's a labor of love that deserves your attention.
We invite you to watch their captivating videos here and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.
We're also inviting you to explore the gear, sponsorships, and boat partnerships highlighted in the "Another Day Working on Our Aluminum Catamaran" video description, or directly on YouTube. By engaging with these offerings or purchasing services and items, you directly support Sailing Life on Jupiter, their collaborators, and the brands they're associated with.
To ensure you never miss an offshore update, consider visiting their official YouTube Channel to subscribe, like, and join their community directly.
If you have any feedback, corrections, or additional information about Sailing Life on Jupiter or their videos, please use the comment form below to share your thoughts with us.
Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!
Another Day Working on Our Aluminum Catamaran! Engine Mount Repairs, Boat Maintenance, Cleaning & DIY Projects as we get ready to sail again.
If you get value from our videos whether entertainment. education or inspiration show your appreciation by supporting our channel.
▶️Visit Our Website: https://www.sailinglifeonjupiter.com
▶️ SUPPORT US HERE 👇:
JOIN our “PRIME” crew on PATREON for early video releases, NO ADDS, weekly video REALTIME updates, private facebook group, video calls , “FREE CONSULTING” and even come sailing with us!!!
▶️Support us on Patreon: https://www.patreon.com/LifeonJupiter
▶️Support us on Paypal: https://www.paypal.me/SJRohan
▶️Just buy us a coffee: https://www.buymeacoffee.com/lifeonjupiter
▶️Amazon storefront: https://amzn.to/3xv7STq
As an Amazon Associate I earn from qualifying purchases.
-------
▶️Please Subscribe: https://www.youtube.com/@SailingLifeonJupiter
-------
▶️Save money. Thank you to our current partners and affiliates!
• Calpha Solar panels: https://bit.ly/47CVJIt
• BLUETTI SwapSolar Ecosystem (AC180T & MultiCooler): https://bit.ly/49rUIFc
• BLUETTI Powerstation : https://shareasale.com/r.cfm?b=1745428&u=4026550&m=108816&urllink=&afftrack=
• Setpower portable fridge: https://bit.ly/41kBtKq
• Litime Lifepo batteries : https://www.litime.com/?ref=CQX_D-NhKgD2bF
• HALOVIEW BACK UP CAMERA : Get 5% off discount code: SailingLifeonJupiter
https://www.haloview.com/byte-tango-bt11-1080p-rear-view-mirror-backup-camera-system-with-bsd.html?acc=768
• UGO Waterproof BAG: https://ugowear.com?aff=38
• Custom Boat/RV mattresses :https://wildernessrvmattress.com/?aff=45
• EPOCH BATTERIES : https://www.epochbatteries.com/?rfsn=8388218.08c2084
• Rattan ebikes : +Exclusive discount code: JR150 (users enjoy $150 off 3 ebikes from Quercus, Pinus, Sequoia)
https://shareasale.com/r.cfm?b=1989890&u=4026550&m=123476&urllink=&afftrack=
• Hiboy Official EX6 Long Range Ebike: https://www.hiboy.com/products/hiboy-ex6-step-thru-fat-tire-electric-bike
Hiboy Amazon EX6 Long Range Ebike: https://www.amazon.com/dp/B0CJXV38DY?maas=maas_adg_2B5B7E27BC85D3E159CAC8CF9762CBF6_afap_abs&ref_=aa_maas&tag=maas
• Hcalory Portable Diesel Heater : https://amzn.to/40HbxtM
15%off Discount code: 150SAILING
• Total Boat Paint : https://www.totalboat.com/?sca_ref=8363251.2FbSFfpUFC
• Seesii AngleGrinder :https://amzn.to/4ndX2Xn
-------
▶️MUSIC:
• All music from: https://www.epidemicsound.com/
• Get a 30 days free trial using this link: https://www.epidemicsound.com/referra...
-------
▶️Follow us on:
• Instagram: https://www.instagram.com/lifeonjupiter2
• Twitter: https://twitter.com/LifeonJupiter2
• Facebook: https://www.facebook.com/LifeonJupiter
-------
▶️For business inquiries: [email protected]
-------
▶️© Sailing Life on Jupiter 2022
-------
#sailing #aluminum #aluminium #aluminumboats
Explore the most recent voyages. Subscribe to the channel to never miss an update!