Sailboat refit YouTube Videos
Showing 811-825 of 939 results
SAILBOAT DODGER FAIL! Ep 122
No-one was really sure they knew what they were doing. Including the canvas guys. Can Ton come to the rescue? Subscribe for more sailing videos: https://ftbyoutube.page.link/subscribe We finally show you how we sorted out that diesel leak! The work goes ...
The Last Projects before we start Sailing (The Sailing Family) Ep.46
http://www.TheSailingFamily.com - Tavarua is on the water again and everything is fine. The indoor refit is going on and this week I did a lot of different but important projects like mounting the new autopilot, fixing the mast steps, making a DIY dinghy c...
One Blister, one Hole but on the Water again (The Sailing Family) Ep.45
http://www.TheSailingFamily.com - After finishing the antifouling paint a mechanic came to make a service for the motor - but you cannot believe whats happened - a nightmare. But for every problem there is a solution. Never give up! So my week has been a l...
Ep 53 Sail P0rn (Sailing Talisman) Cartegena to Alicante
We get up early to make a long day run to Alicante, Spain. The sailing conditions were epic, and although we were close hauled for the first half, later it was beam-on and fast. What a joy it was!
Refit of our Hallberg-Rassy started (The Sailing Family) Ep.44
http://www.TheSailingFamily.com - Before we will enjoy our Endless Summer Sailing Trip we have to refit our Hallberg-Rassy 352. I started to remove the old antifouling and also the primer and to but on new layers. This is really a nasty job - but its just ...
Installing a GPS / AIS / VHF combo antenna on the stern pulpit of a sailboat
On this episode I show you guys how I went about installing my Digital Yacht GPS / AIS / VHF combo antenna for my Digital Yacht iAis receiver. I wanted to install it on the stern rail and to run the cables down the tube of the stern pulpit and into the aft...
Back in Panama – Mold Attack (The Sailing Family) Ep.43
http://www.TheSailingFamily.com - Yes I’m back in Panama - back at our sailboat and a lot of work is waiting for me - more than I have expected. So follow me on my first week in panama and our Endless Summer Sailing Trip. We hope by sharing this adventu...
Ep 52 Genset Repair (Sailing Talisman)
We finally tackle a finicky Fischer Panda genset that's been shutting itself down prematurely. I'm sure some viewers will see too much time spent barking up the wrong trees, but the point is to show how hard it can be to diagnose problems.
Removing the Icebox on an Alberg 30 – Sailing Vessel Triteia
Ahoy Friends! Here is another one of my project throw back videos. In this video you get to see me go through all of the steps of removing the factory Ice Box from my 1965 Alberg 30. The chart table and nav station will later occupy the space this outdate...
Ep 51 Sailing Talisman from Ceuta, Spanish Morocco to Cartagena, Spain
We finally head east and north, across a long expanse of Mediterranean open water. It's a big passage, nothing like our short shakedown across the Strait of Gibraltar. We pass through weather fronts and sail during the night dodging shipping traffic.
Drilling Holes in the Deck and the Hull for Head Fittings on an Alberg 30 – Part 4
Finally wrapping up this four part series on my head build out! In this episode I measure and drill out the deck fitting and the hole for the vent in the hole on my Alberg 30. Boats of this age do not have a cored hull so the beauty is you don't need to se...
Hooking up the plumbing on the head on an Alberg 30 – Part 3
On this episode I install the ports on the holding tank, get all the plumbing sorted out, install the Y valves and figure out the best way to align and find the best spot for the macerator pump. The hose that leads to the Thru-hull would NOT go on so I end...
Ep 49 Big Weather in Gibraltar, then off to Ceuta, Spanish Morocco
We see a weather window to leave Gibraltar for Ceuta, but then get hammered on both ends.
Dry Fitting Holding Tank and Cutting Access Hole on an Alberg 30 – Part 2
On this episode I do a dry fit of the new holding tank I am installation on my 1965 Alberg 30. I then move on to cutting out bases for the Y-Valves and finally cut an access hole in the top of my holding tank. I make my project videos on the slow side le...