Reset Password

Experience...
Watercraft...
Experience...

USD 0 to USD 10,000

Metal lathe YouTube Videos

Showing 1-10 of 10 results
Installing a PYI PSS Dripless Shaft Seal on a Vintage Sailboat
Sailing Triteia
Installing a PYI PSS Dripless Shaft Seal on a Vintage Sailboat
SEASON 6 / The Haul Out : Episode #131 : Wrestlin' the PSS Shaft Seal into place On this episode we enter the MAD DASH phase of the haul out! What we don't mention in the video is that we were racing the clock to get the prop shaft and PSS installed befor...
May 18, 2020
Language: EN
Play Time: 00:19:49
Acorn to Arabella – Journey of a Wooden Boat – Episode 83: Riveting Test and Prop Shaft Assembly
Acorn To Arabella
Acorn to Arabella – Journey of a Wooden Boat – Episode 83: Riveting Test and Prop Shaft Assembly
Sometimes, boatbuilding is all about big showy pieces coming together. But much of the time it is also working with small details. This week, we focus on some of these details that we are going to have to figure out before we move on from the prop shaft ...
Oct 11, 2019
Language: EN
Play Time: 00:25:04
Acorn to Arabella – Journey of a Wooden Boat – Episode 82: Working on Prop Shaft Fittings
Acorn To Arabella
Acorn to Arabella – Journey of a Wooden Boat – Episode 82: Working on Prop Shaft Fittings
We are getting farther up the hull with the planking and as we do so, we are nearing the point at the stern where the propeller shaft will go through. We need to get this hole bored before we plank past it because we are going to need to be able to align ...
Oct 04, 2019
Language: EN
Play Time: 00:22:22
ROV Hull Components – Part 1
SV Seeker
ROV Hull Components – Part 1
Super Dave gave us some lessons on the metal lathe and helped out a couple of weekends and between the 3 of us we have almost all of the hull components ready. And even our bad part passed the 2000 psi pressure test.
Mar 12, 2014
Language: EN
Play Time: 00:09:54
ROV Camera Housing – Part 1
SV Seeker
ROV Camera Housing – Part 1
Super Dave spent the weekend teaching Kay how to run the metal lathe and making the ROV's pressure housing for the Aft Camera. After a quick redesign and it's a much easier part to make, but it and the acrylic dome we make will have to survive 2000 psi in...
Feb 18, 2014
Language: EN
Play Time: 00:08:06
Watertight Doors – Part 2 – Dog Parts
SV Seeker
Watertight Doors – Part 2 – Dog Parts
Lots of little, time sucking parts needed for our 3 watertight doors.
Jan 26, 2013
Language: EN
Play Time: 00:09:57
DIY Boat Propeller – Part 8 – Machining the Groove
SV Seeker
DIY Boat Propeller – Part 8 – Machining the Groove
It's asking a lot of our CNC plasma/router table but with help from Super Dave we turned it into a successful CNC lathe so we could mill the grooves in our home make propeller blades that will fit our Hundested Controllable Pitch Propeller system.
Jul 02, 2012
Language: EN
Play Time: 00:13:49
Hundested Rebuild – Part 2 – Machining the Distributor Ring
SV Seeker
Hundested Rebuild – Part 2 – Machining the Distributor Ring
If we get this one part right it will save us from buying $3,400 of parts from Hundested. Great to pay for the lathe with the first part!
Mar 06, 2012
Language: EN
Play Time: 00:09:50
Grizzley 4003 12×36 Metal Lathe
SV Seeker
Grizzley 4003 12×36 Metal Lathe
Feb 23, 2012
Language: EN
Play Time: 00:03:55
Engine Rebuild 101 – Part 8 – Cutting Piston Ring Grooves
SV Seeker
Engine Rebuild 101 – Part 8 – Cutting Piston Ring Grooves
Apr 21, 2011
Language: EN
Play Time: 00:05:19