Bronze YouTube Videos
Showing 226-240 of 254 results

Mast Step and Alignment – Episode 152 – Acorn to Arabella: Journey of a Wooden Boat
With wrapping up the bronze floors comes working on the mast step. This wild looking piece is built up out of live oak and black locust and looks more like a sculpture than a structural element in the boat! We also check alignment on Arabella to see if ev...
Last Bronze Floors and a Mast Step – Episode 151 – Acorn to Arabella: Journey of a Wooden Boat
We finally get to finish up the work on the bronze floors. We had about six sets of frames that needed to go in once we removed the molds. These last sets all needed bronze floors made up for them as we couldn't make those on our first go around. That m...
Clean Bilge! – Episode 150 – Acorn to Arabella: Journey of a Wooden Boat
Building a boat can seem like an incredibly daunting task. One thing that has gotten us through these years is seeing it a lot of little things that need to be done and pieces that need to go together. This episode is very much dedicated to that ideology...
Cockpit Mockup – Episode 149 – Acorn to Arabella: Journey of a Wooden Boat
There are a lot of exciting things coming together at the moment. Steve installed the rest of the tie rods, Alix finished the sill for the deckhouse to sit on and we made a mockup of the cockpit! One task completely finished, one setting us up for the de...
Pouring Bronze / Fastening Floors – Wooden Boat Rebuild (EP81)
Rebuilding a historic sailing yacht - Pouring Bronze / Fastening Floors (EP81) Support; http://www.sampsonboat.co.uk/support Become a Patron; http://www.patreon.com/sampsonboatco ---- EPISODE 81. Having poured all the smaller bronze Floors, we have to b...
BoatBuilding – Finishing the Transom (EP76)
Rebuilding a historic sailing yacht - Finishing the Transom / More Floors (EP76) Support; http://www.sampsonboat.co.uk/support Become a Patron; http://www.patreon.com/sampsonboatco ---- EPISODE 76. In this episode I focus on the final install of the tra...
BoatBuilding – Casting Bronze Floors (EP75)
Rebuilding a historic sailing yacht - Casting Bronze Floors (EP75) Support; http://www.sampsonboat.co.uk/support Become a Patron; http://www.patreon.com/sampsonboatco ---- EPISODE 75. In this extra-length episode, Pete and Clark show the process of maki...
How to Install Thru Hull Fittings – TruDesign | Sailing Sunday
We replaced every Thru Hull and Seacock on Sunday with TruDesign. This is a simple step-by-step guide on how we did it.
Acorn to Arabella – Journey of a Wooden Boat – Episode 82: Working on Prop Shaft Fittings
We are getting farther up the hull with the planking and as we do so, we are nearing the point at the stern where the propeller shaft will go through. We need to get this hole bored before we plank past it because we are going to need to be able to align ...
Acorn to Arabella – Journey of a Wooden Boat – Episode 80: Sawn Frames and Bronze Floors
In last week's episode, we went into detail about how we are fabricating the forward sawn floors. From how we are taking measurements using tick sticks and a template to how we are cutting our rolling bevel down the frames without a ship's saw. In this ep...
Acorn to Arabella – Journey of a Wooden Boat – Episode 65: Installing the Bronze Floors
The prep is over with and it is finally time to install the bronze floors! We have invested so much time, energy and money in these and it is such a gratifying feeling to finally see them put in place. In the end, the installation went very smoothly and ...
Acorn to Arabella – Journey of a Wooden Boat – Episode 64: Setup for Bronze Floor Installation
The bronze floor timbers have been a lot of work but it is all paying off. We spend some time prepping everything so that we can finally get to installing these beauties in their places for good! Each faying surface will need treatment before we can place...
Acorn to Arabella – Journey of a Wooden Boat – Episode 62: Fitting the Engine Beds
We pushed really hard to get the bronze floors finished up so they could be sitting in their places during the open house. In this episode we show how we got the floors ready to start fabricating the supports for the engine beds. Since everything fits in...
Acorn to Arabella – Journey of a Wooden Boat – Episode 61: Tacking Floors and Steaming Frames
We're moving right along with our silicon bronze floor timbers. We tacked most of the floor pieces together in preparation for welding them in batches. Before we can finish making the rest of the floor timbers though, we need to replace the frames that w...