Fiberglassing In Winter Was Way Easier - Ep. 403 RAN Sailing

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
It’s 1270 mm wide and that was a problem already on the outside. That was really hard work, reaching the other end because you couldn’t go on the other side because that was freshly laminated. Now that will be an even bigger problem since yeah, you can’t walk on the hull.

What we’re going to do is to fold this cloth in the middle like so Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
It’s the middle of summer, Ver is on summer holiday, and he’s spending a few days with Yan’s mother. I was sending the epoxy Yuan added last week, and Yuan was measuring for the fiberglass [Music]. We’re almost ready now to start laminating the first section of the inside of the hull [Music].

Yesterday, we did a lot of prep work and today I still have some prep work to do. The plan is to start laminating once the temp is going down so around 3:00 or so this afternoon. I have changed the way we’re going to do this slightly compared to how we did it on the outside of the hull.

The main problem now working on the inside of the hull is to reach all the areas with the cloth It’s 1270 mm wide and that was a problem already on the outside. That was really hard work, reaching the other end because you couldn’t go on the other side because that was freshly laminated. Now that will be an even bigger problem since yeah, you can’t walk on the hull.

What we’re going to do is to fold this cloth in the middle like so Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Welcome back to RAN Sailing! Last week, we did a little garden project and then continued preparing for laminating the inside of the boat hall. Yan also built a platform stairs to get in and out of the boat easier. It’s topscore five strawberries out of five [Music].

It’s the middle of summer, Ver is on summer holiday, and he’s spending a few days with Yan’s mother. I was sending the epoxy Yuan added last week, and Yuan was measuring for the fiberglass [Music]. We’re almost ready now to start laminating the first section of the inside of the hull [Music].

Yesterday, we did a lot of prep work and today I still have some prep work to do. The plan is to start laminating once the temp is going down so around 3:00 or so this afternoon. I have changed the way we’re going to do this slightly compared to how we did it on the outside of the hull.

The main problem now working on the inside of the hull is to reach all the areas with the cloth It’s 1270 mm wide and that was a problem already on the outside. That was really hard work, reaching the other end because you couldn’t go on the other side because that was freshly laminated. Now that will be an even bigger problem since yeah, you can’t walk on the hull.

What we’re going to do is to fold this cloth in the middle like so Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Welcome back to RAN Sailing! Last week, we did a little garden project and then continued preparing for laminating the inside of the boat hall. Yan also built a platform stairs to get in and out of the boat easier. It’s topscore five strawberries out of five [Music].

It’s the middle of summer, Ver is on summer holiday, and he’s spending a few days with Yan’s mother. I was sending the epoxy Yuan added last week, and Yuan was measuring for the fiberglass [Music]. We’re almost ready now to start laminating the first section of the inside of the hull [Music].

Yesterday, we did a lot of prep work and today I still have some prep work to do. The plan is to start laminating once the temp is going down so around 3:00 or so this afternoon. I have changed the way we’re going to do this slightly compared to how we did it on the outside of the hull.

The main problem now working on the inside of the hull is to reach all the areas with the cloth It’s 1270 mm wide and that was a problem already on the outside. That was really hard work, reaching the other end because you couldn’t go on the other side because that was freshly laminated. Now that will be an even bigger problem since yeah, you can’t walk on the hull.

What we’re going to do is to fold this cloth in the middle like so Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.

Fiberglassing In Winter Was Way Easier – Ep. 403 RAN Sailing

Welcome back to RAN Sailing! Last week, we did a little garden project and then continued preparing for laminating the inside of the boat hall. Yan also built a platform stairs to get in and out of the boat easier. It’s topscore five strawberries out of five [Music].

It’s the middle of summer, Ver is on summer holiday, and he’s spending a few days with Yan’s mother. I was sending the epoxy Yuan added last week, and Yuan was measuring for the fiberglass [Music]. We’re almost ready now to start laminating the first section of the inside of the hull [Music].

Yesterday, we did a lot of prep work and today I still have some prep work to do. The plan is to start laminating once the temp is going down so around 3:00 or so this afternoon. I have changed the way we’re going to do this slightly compared to how we did it on the outside of the hull.

The main problem now working on the inside of the hull is to reach all the areas with the cloth It’s 1270 mm wide and that was a problem already on the outside. That was really hard work, reaching the other end because you couldn’t go on the other side because that was freshly laminated. Now that will be an even bigger problem since yeah, you can’t walk on the hull.

What we’re going to do is to fold this cloth in the middle like so Instead of 1270 mm, we will have half of that, which is 635 mm. That’s pretty easily to reach across with rollers so we can keep good pressure on rollers because that’s important not just to reach you need to have a lot of pressure as well and even pressure to get all the air out and get the cloth really saturated

The cloth we’re using is actually lighter than the one we used on the outside, it’s 450g/m². Initially, the plan was to use three layers of this, which is just below 60% of the glass that we’ve been using on the outside and that was you know, on the limit.

By folding it, we will have four layers instead of three Since we want to have everything wet in wet, we’re skipping the twill weave on top since it’s not really needed on the inside. The print-through isn’t really a problem here. So instead, the hull will be a little bit heavier on the inside, but we’ll have the correct amount of glass compared to the outside straight away.

Actually, we will have 1,800 g/m² of glass per square meter on the inside and we have 2,400 g/m² on the outside. So a little bit more balanced. That’s not really an issue when you’re doing U-strip planking like we’re doing if it would’ve been PVC foam, then it’s more important to have a fully balanced sandwich like you have the same amount of glass on the outside and inside.

The main advantage is that we can quite easily reach everywhere now One challenge, though, is that it takes a bit longer to saturate the cloth because we’re using half the width. But then again, it’s summer now so compared to how it was to saturate the cloth in the winter, it’s much faster

One of the key learnings from this experience is that a primer layer isn’t really needed on the inside, especially since we’re using a saturation table I know that a lot of people have commented on this with the worry that the cedar will Wick too much of the epoxy from the fiberglass so we get a starved laminate. But that’s not the case, actually, the cedar doesn’t Wick a lot of epoxy at all on this face of the wood. So you can’t really compare it to like balsa or anything like that. This behaves way different than that

It’s time for Yan to make holes and suck out the air from the bubbles [Music]. He mixed some epoxy, but we don’t need it. It’s just enough to make the hole so the air can go out. There are so many ways I’m getting sweaty! Are you sweaty? You’re dripping. I’m totally soaked in this suit and wearing underwear underneath.

The process is challenging but satisfying We’ve done two pieces already, and it’s really hard work. It’s exhausting, and we’re soaked in plastic. We need to think about this and find a better way next time.

After some reflection, Yuan believes that the main cause of our struggles is likely that the weather shifted yesterday, causing the temp to go up instead of down when it was supposed to [Music]. So we need to be more aware of temperature fluctuations in the future and plan accordingly.

It’s time for round two today as Ver points out that the temperature has already started to go down at 4:00 today. We have high hopes that it will be easier this time around!

The second attempt is much more successful We managed to complete three pieces of fiberglassing tonight and it went so much better than last time. We learned a lot from our mistakes and are now using different techniques that have made the process easier.

For example, we’re cutting the cloth where we folded it, which helped reduce any creases or folds that might have caused issues previously. The process has become much smoother, with both of us working in harmony to achieve the desired result without the air bubbles that plagued our first attempt.

All in all, things are going much more smoothly this time around. We’ve made adjustments and learned from our mistakes, proving once again that even when something seems impossible at first, perseverance pays off!

Key takeaways
  • Check the temperature log before starting to laminate, as fluctuations can lead to unexpected challenges.
  • When folding fiberglass cloth for difficult-to-reach areas, consider cutting it at the fold to minimize creases.
  • Trust in your saturation table and skip using primer on the inside when using cedar planking.
Support our production and join the RAN Sailing crew ~ with livestreams, meet-ups & get in direct contact with us: https://www.patreon.com/ransailing

We knew it was going to be different laminating the inside of the hull but get a bit shocked on how hard it was. We learn some lessons and try again!

We are a Swedish family who have sailed the world since 2016 while sharing the adventures here on YouTube. While we are still sailing, our main focus now a days is building RAN III, a 50 ft sailboat that we are building from scratch. We post a new episode every Friday so make sure to subscribe and hit the bell to be the first to know when there is a new episode!

MERCH: https://ransailingstore.com/
Sustainable shirts, tees, bags and more in 100% organic cotton, designed by us!

PRODUCTS & CAMERA GEAR: https://www.amazon.com/shop/ransailing
We have collected some of the products we use in our cruising life and video making in our Amazon shop. If you buy any of the items from our shop, we get a small "ka-ching" in our cruising kitty (no extra cost for you). Thank you so much and thank you to Amazon Influencer program.

CONNECT WITH US
- Website: http://ransailing.se
- Instagram: http://www.instagram.com/ransailing
- Facebook: http://www.facebook.com/ransailing

Music credits: http://www.epidemicsound.com

Love,
Malin, Johan & Vera

Fiberglassing In Winter Was Way Easier - Ep. 403 RAN Sailing Locations

  • Skåne (59.4762392,13.3392076)

Note of Recognition for RAN Sailing

At WeBoating.com, we profoundly acknowledge the unwavering dedication that RAN Sailing and other creators invests in crafting each and every video. Their passion for delivering exceptional content shines through every frame, and it's a labor of love that deserves your attention.

We invite you to watch their captivating videos and actively engage with their content, including their social media links above. Liking, commenting, and sharing their work goes a long way in fueling their creative fire.

We're also inviting you to explore any sponsorships and partnerships highlighted in the video description of "Fiberglassing In Winter Was Way Easier - Ep. 403 RAN Sailing", or directly on YouTube. By considering their offerings or purchasing services and items, you not only support RAN Sailing but also the brands and collaborators they're associated with.

If you have any feedback, corrections, or additional information about RAN Sailing or their videos, please use the comment form below to share your thoughts with us.

Thank you for being a part of our community and supporting the creators we cherish. Your time and support truly matter!

RAN Sailing Lastest Videos

Showing 1-6 of 473 results
We Weighed The Boat – And The Numbers Surprised Us! – Ep. 451
RAN Sailing
We Weighed The Boat – And The Numbers Surprised Us! – Ep. 451
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing We are a Swedish family who have sailed the world since 2016 while sharing the adventures here on YouTube. Wh...
Reinforcement Finished! Starting the Side Decks at Last – Ep. 448 RAN Sailing
RAN Sailing
Reinforcement Finished! Starting the Side Decks at Last – Ep. 448 RAN Sailing
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing We have come to the last jobs before finishing the reinforced bulkheads and then we start working on the side...
Titanium Chain Plates? And a Surprise Obstacle – Ep. 447 RAN Sailing
RAN Sailing
Titanium Chain Plates? And a Surprise Obstacle – Ep. 447 RAN Sailing
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing It's Friday again and this week we start building the reinforced bulkhead for port side. Which material will ...
What Does It Take To Build Your Own Boat? – Ep. 446 RAN Sailing
RAN Sailing
What Does It Take To Build Your Own Boat? – Ep. 446 RAN Sailing
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing This week we talk about what it takes to build a boat, the challenges and if it's worth it. We are a Swedish...
Tabbing the Most Critical Bulkhead on the Boat – Ep. 445 RAN Sailing
RAN Sailing
Tabbing the Most Critical Bulkhead on the Boat – Ep. 445 RAN Sailing
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing In this week's episode Johan finish the reinforcement bulkhead for the shrouds and install it in the boat. Th...
Shroud Loads Are Brutal: This Is How We Handle Them – Ep. 444 RAN Sailing
RAN Sailing
Shroud Loads Are Brutal: This Is How We Handle Them – Ep. 444 RAN Sailing
Support our production and join the RAN Sailing crew ~ get in direct contact with us, livestreams and meetups: https://www.patreon.com/ransailing This week we build a bulkhead to take up the loads from the lower shrouds of the mast which is a crucial part...

Something AWESOME is coming!
Be the FIRST to know⛵

Sign up for exclusive updates and be the first to hear when we go live!
Get sneak peeks, exciting announcement, and special content straight to your inbox!

We don’t spam! Read our privacy policy for more info.

WeBoating
Logo
Shopping cart